Routine maintenance – Precautions for LED display –
With the widespread use of LED displays, there are increasing usage problems.
In order to better use LED display related products, we have made some feasible summaries on related usage precautions and daily maintenance.
01. Precautions for use environment
– POINTS FOR ATTENTION-
1. The working environment temperature range is -20℃≤t≤50℃, and the working environment humidity range is 10% to 90%RH;
2. Avoid use or storage in high temperature, high humidity, high acid/alkali/salt environments;
3. Keep away from flammable items, gases, and dust;
4． During transportation, avoid strong collisions and avoid collisions with sharp objects;
5. When the ambient temperature is too high or the heat dissipation conditions are not good, be careful not to use the screen with the screen open for a long time;
6． When an LED display with a humidity exceeding the specified humidity is powered on, it will cause corrosion of parts and even short circuit, causing permanent damage;
7． It is strictly forbidden to allow water, iron powder and other metal objects that are easily conductive to enter the screen. The LED display screen should be placed in a low-dust environment as much as possible. Large dust will affect the display effect, and too much dust will cause damage to the circuit. If water enters for any reason, please cut off the power immediately and wait until all components inside the screen are dry before use.
02. Precautions when switching the screen
– POINTS FOR ATTENTION –
1. Open the screen: first turn on the control computer so that it can operate normally, and then turn on the large LED display screen;
2. Turn off the screen: first turn off the power of the LED screen, turn off the control software, and then turn off the computer correctly; (turning off the computer first without turning off the display will cause highlights to appear on the screen and burn out the lamp, with serious consequences)
3. The interval between switching the screen on and off should be greater than 5 minutes;
4． Avoid opening the screen in a completely white screen state, because this is the maximum power state, which has the largest impact current on the entire power distribution system.
03. Power supply precautions
– POINTS FOR ATTENTION –
1. The LED module is powered by DC +5V (operating voltage: 4.2~5.2V). It is prohibited to use AC power supply. It is strictly forbidden to reverse the positive and negative poles of the power supply terminals (note: once reversed, the product will be burned or even cause a serious fire);
2. Power supply voltage of LED display: 220V±10% Frequency: 50HZ±5%;
3. Safe ground contact is reliable, ground wire and neutral wire are isolated reliably, and the power supply is connected away from high-power backup;
4． If any abnormalities such as short circuit, tripping, wire burning, smoke, etc. are found, power on and test should not be repeated and the problem should be found in time;
5. Keep the power supply stable and provide grounding protection to avoid lightning strikes. Do not use it under harsh natural conditions, especially strong lightning weather;
6． The power supply for the large screen must be supplied step by step, because the maximum power state of the entire screen will have an impact on the entire power distribution system;
7． The LED display screen is not allowed to play the highest brightness all-white picture for more than half an hour to avoid excessive current, heating of the power cord, damage to the LED lamp, and affecting the service life of the display screen. It is recommended to mainly play dynamic videos;
8. During the use of LED display products, the power cannot be turned on and off continuously, and there should be at least 1 minute between operations;
9. Non-professionals are prohibited from touching the internal circuits of the large LED display screen to avoid electric shock or damage to the circuits. If there is a problem, please ask professionals to repair it.
04. Cleaning precautions
– POINTS FOR ATTENTION –
1. Regular cleaning and maintenance: The large LED full-color display screen is exposed to wind, sun, and rain in the outdoor environment for a long time. Even if the indoor LED display screen is used for a long time, more dust and traces of rain erosion will accumulate on the screen. This will It needs to be cleaned regularly and promptly to prevent it from affecting the viewing effect;
2. To clean the surface of the module, please use a soft-bristled brush and brush gently. It is prohibited to use any liquid substance to clean the surface of the LED module, otherwise the LED lamp beads may be damaged;
3. Correct wiping: The surface of the large LED display screen can be wiped with alcohol, or dusted with a brush or vacuum cleaner. It cannot be wiped directly with a wet cloth.
05. Moisture-proof and storage requirements
– POINTS FOR ATTENTION –
1. Storage temperature requirements: ambient temperature -40℃≤t≤60℃. After opening the package, LED products must be stored in an environment with a temperature <30℃ and a humidity <60%;
2. According to the environmental conditions of the display body and control parts, avoid insect bites and place anti-rodent pesticides if necessary;
3. The LED display cannot be turned off for a long time. In a high-humidity environment, if the screen has not been used for more than 3 days, a preheating lighting method must be used every time the screen is lit: 30%-50% of the brightness must be preheated for 4- 8 hours, and then adjust to normal brightness (80%-100%) to light up the screen to remove moisture so that there is no abnormality during use; if the screen has not been used for more than 7 days, it is necessary to light up the screen each time Adopt preheating lighting method: 30%-50% brightness is preheated for more than 12 hours, and then adjusted to normal brightness (80%-100%) to light up the screen, thereby eliminating moisture so that there are no abnormalities during use. .
If you find this article useful, please like and save it
-END
